#PAGE_PARAMS# #ADS_HEAD_SCRIPTS# #MICRODATA#

EFFECT OF THE PLACEMENT OF THE INERTIAL SENSOR ON THE HUMAN MOTION DETECTION


There are numerous possibilities of assessments of the human activity, offered by the ActimedARM -a wearable inertial sensor we developed. This device features a triaxial magnetometer, a trixial accelerometer, a micro-processing unit, a Zigbee module and a µSD card. Its embedded algorithms make it able to compute postures, transfers of the subject and also to characterize the walking episodes. We recently succeeded in computing the relative displacements of the sensors, from double integration of the acceleration signals, in order to qualify specific physical activities such as rising from chairs or stools. The experiments highlighted the impact of the location of the sensor on the body on the correlation between objective motion and signals processed from acceleration measurements, showing a better correlation coefficient of 11.41% when the sensor is located on the navel.

Keywords:
actimetry monitoring, embedded systems, inertial sensors


Authors: Julien Collet 1;  Martin Cerny 2;  Ludovic Delporte 3;  Norbert Noury 1
Authors place of work: Institute of Nanotechnology of Lyon (INL-UMR5 70), INSA Lyon, Villeurbanne, France 1;  VSB Technical University Ostrava, Ostrava, Czech Republic 2;  Neurologic Science Center of Lyon (CNRL), Lyon, France 3
Published in the journal: Lékař a technika - Clinician and Technology No. 4, 2014, 44, 21-24
Category: Původní práce

Summary

There are numerous possibilities of assessments of the human activity, offered by the ActimedARM -a wearable inertial sensor we developed. This device features a triaxial magnetometer, a trixial accelerometer, a micro-processing unit, a Zigbee module and a µSD card. Its embedded algorithms make it able to compute postures, transfers of the subject and also to characterize the walking episodes. We recently succeeded in computing the relative displacements of the sensors, from double integration of the acceleration signals, in order to qualify specific physical activities such as rising from chairs or stools. The experiments highlighted the impact of the location of the sensor on the body on the correlation between objective motion and signals processed from acceleration measurements, showing a better correlation coefficient of 11.41% when the sensor is located on the navel.

Keywords:
actimetry monitoring, embedded systems, inertial sensors

Introduction

Activities of Daily Living (ADL) are directed by vital needs as for example sleeping or feeding. These activities reflect both our physical and mental conditions. Furthermore, it is known that the ability of an individual to complete physical tasks can help diagnosing diseases such as chronic obstructive pulmonary diseases (COPD) [1] or mobility affecting pathologies [4].

Actimetry studies the succession of postures (sitting, standing, lying and walking) in which a subject was during a period of time to evaluate its characteristics. There are mainly two kinds of devices dedicated to this tracking: gold-standard systems using sets of cameras and inertial devices [2, 3]. The first category can produce objective and exhaustive assessment of the activity by implementing complex image-processing algorithms. But these systems are limited to laboratory premises and have important disadvantages such as requiring powerful calculation systems and the user to wear tags over the body. The other category –namely, the inertial sensors- have emerged due to the recent advances in the MEMS industry [2, 3]. The decreasing sizes of devices made possible the design of small wearable systems for the monitoring of the activity on a daily basis.

We designed and fabricated such an embedded system: The ActimedARM. The design was driven by consideration of energy consumption and acceptability. Recently, we performed experiments to investigate the feasibility of the assessment of the motion and the impact of the sensor location on an individual body. To achieve this, displacement was computed from ac-celeration measurements and compared to the data obtained from an objective source.

Materials and methods

Material

The ActimedARM was designed around a 32bit ARM powered processing unit. It also embeds a three-axis magnetometer, a three-axis accelerometer, a Zigbee (802.15.4) module and a µSD card. A 3.6 Volts Lithium-Ion battery [4], power the whole system.

The core of the system, the STM32F103RE (STMicroelectronics), was chosen for its power in terms of calculations (Cortex-M3 core), its integrated peripherals (SPI, USART, ADC, RTC) and its low-consumption (28 mA maximum in operation, 25 µA in sleep mode). The µSD card offers a great compromise between storage capacity and physical dimensions. It is also natively handled by the processing unit (a SDIO port is available and a dedicated library is provided by the manufacturer).

The ADXL345 (Analog Device) is an autonomous system that communicates the values of accelerations on a SPI bus. It was chosen for its low-power characteristics (3.6 V, 65 µA@25 Hz) and is in sleep mode most of the time [4].

The HMC1043 (Honeywell) is a three dimensional magnetometer and implements a Wheatstone bridge type circuit and an amplification stage to feed the analog-to-digital converter. The system also features a reset circuit to compensate the drift in time of the magneto-resistors [4] and is usually read each second by the processing unit.

Mechanical considerations and hardware performances

The design stage was driven by considerations of acceptability. In terms of physical dimensions, the ActimedARM has the following dimensions: 28x30x12 mm without the power battery. The privileged location for the sensor was on the bust, for a better acceptability and discretion. Also, the bust was found to be more representative of the whole body motion and therefore more suitable for a global asses-sment of the activity. During the latest experiments, other locations were investigated such as on the navel or on the pelvis.

The second design goal was to create a system able to monitor the activity during long periods of time. To do so, its consumption must be kept low. In radio-operation mode (the radio module is on), the autonomy is 8 days (resp. 24 days) on a 1200 mAh battery (resp. 3600 mAh). In data-logger mode (the radio module is off), the autonomy reaches 10 days (resp. 32 days) [4].

Embedded Algorithms

In normal conditions, the software iterates every second (1 Hz). In this iteration, 25 samples of acceleration and one sample of magnetic field are stored and processed. The processing starts with low-pass filtering of the acceleration signals then the detection of the posture, the transfers and the walking episodes. The quaternion representing the attitude of the subject is then computed and, depending on the configuration file, the data is sent through the ZigBee module to the host computer and/or written on dedicated files on the on board µSD card [4].

Fig. 1: The ActimedARM (center), a μSD card (right) and a battery (left).
Fig. 1: The ActimedARM (center), a μSD card (right) and a battery (left).

The detection of the posture is elaborated from the vertical component of the acceleration modulus being maximum (resp. minimum) when the subject is standing (resp. lying),

The classification of the transfers is realized by analyzing the changes in postures over time for stand to lying and lying to stand transfer. In the more complex case of sit-to-stand and stand-to-sit, an algorithm searches for a phase-shift which occurs during transfers between vertical and horizontal signals.

Fig. 2: Location of the 2 sensors on the subject.
Fig. 2: Location of the 2 sensors on the subject.

When walking, a pseudo-periodic signal due to foot impacts can be detected on vertical accelerations. We can therefore detect walking episodes by tracking peaks in the frequency range 1.1 Hz – 5.4 Hz [4].

Experiments

Two series of experiments were performed, involving 4 male subjects (36 +11.5 yrs, 87.7 +32.57 kg, 1.73 +0.10 m) wearing two ActimedARM: one on the navel and the other on the pelvis.

The experiments consisted in a series of sit-to-stand transitions from a chair and from a stool. The orientation data, computed from the sensors, were then compared to position plot from the video system composed of 7 cameras (type: Eagle, sampling frequency: 200 Hz, resolution: 1.3M pixels, manufacturer: Motion Analysis Inc.). For the motion analysis, thirteen tags were placed on the sensors and on the body.

The inertial sensors were sampled at a frequency of 25 Hz for accelerations and 1 Hz for magnetic field components. One quaternion was computed every second during the experimentations. The sensors modules were in data-logging mode (Zigbee communication module off).

The motion plot was obtained by integrating twice the vertical acceleration recorded by the ActimedARM and opposed to the motion plot from the gold standard-video system, under the Matlab Environment. The algorithm is composed of a first step designed to reduce the integration error by removing the DC component of the signal (subtraction of the mean value), then, two numerical integration steps are processed with a high-pass F.I.R filter (0.12 Hz) used in between to reduce the amount of error on the processed signal.

Then, the computation of the correlation coefficient between signals from ActimedARM and video systems was done from the second sit-to-stand until the last one.

Results

The average correlation between the gold standard video system and the ActimedARM located on the pelvis (respectively on the navel) is 72.37% (resp. 83.78%) as can be seen on Table 1.

Tab. 1. Correlation coefficients between displacement data computed from ActimedARM raw acceleration values and data from the video system.
Correlation coefficients between displacement data computed from ActimedARM raw acceleration values and data from the video system.

The error between signals from our sensors and the objective motion plots from the video system is mainly due to the cumulative errors brought by the integration process when computing displacements data from raw acceleration signals.

Fig. 3: Subject #3, Displacement of the patient during sit-to-stand and stand-to-sit on a chair. Pelvis located ActimedARM processed signals (r.), video (b.).
Fig. 3: Subject #3, Displacement of the patient during sit-to-stand and stand-to-sit on a chair. Pelvis located ActimedARM processed signals (r.), video (b.).

Fig. 4: Subject #3, Displacement of the patient during sit-to-stand and stand-to-sit on a stool. Pelvis located ActimedARM processed signals (r.), video (b.).
Fig. 4: Subject #3, Displacement of the patient during sit-to-stand and stand-to-sit on a stool. Pelvis located ActimedARM processed signals (r.), video (b.).

Conclusion

When looking to results (Table 1), it seems pretty obvious that the navel is a privileged location when assessing the motion during sit-to-stand transitions, with an average correlation coefficient better by 11.41% when located on the navel.

Further experiments still needs to be done to check if this location is optimal for the evaluation of other kinds of physical activities or for the overall assessment of the motion both in terms of accuracy and in terms of acceptability.

Improvements can be made on the motion-processing algorithm to reduce errors due to the integration of noise and numerical errors.

Eventually, a new version of the system is under design to obtain a more accurate and low-power inertial sensor using the latest, more frugal components.

Acknowledgement

This paper has been elaborated in the framework of the project “Support research and development in the Moravian-Silesian Region 2013 DT 1 - International research teams“ (RRC/05/2013). Financed from the budget of the Moravian-Silesian Region.

The authors thank team IMPACT (CRNL, Lyon) for accessing their MouvHandi motion platform. Further-more, a grateful thank is addressed at Etienne Grenier and Osée Rajaiah for their voluntary participation to experimentations.

References

Prof. Norbert Noury

Institute of Nanotechnology of Lyon

INSA Lyon,

Villeurbanne, F-69621

France

E-mail: norbert.noury@insa-lyon.fr

Phone: (+33)4 72 43 74 54


Zdroje

[1] B. Aguilaniu, H. Roth, J. Gonzalez, M. Jondot, J. Maitre, F. Denis, T. Similowski. A simple semi-placed three minutes chair rise test (3CRT) for routine exercise tolerance testing in COPD. Int Journal of COPD, 2014 (under publication).

[2] G. A. L. Meijer, K. R. Westerterp, F. M. H. Verhoeven, H. B. M. Koper, F. Ten Hoor. Methods to assess physical activity with special reference to motion sensors and accelerometers, IEEE-TBME. 1991;38: 221-229.

[3] Bouten C et al. A triaxial accelerometer and portable data processing unit for the assessment of daily physical activity. IEEE-TBME. 1997; 44(3):136-47.

[4] N. Noury, B. Perriot, J. Collet, E. Grenier, M. Cerny B. Massot, E. McAdams. ActimedARM – Design of a Wearable System to Monitor Daily Actimetry, 35th Annual International Conference of the IEEE EMBS, Osaka, 3-7 July, 2013.

Štítky
Biomedicína
Prihlásenie
Zabudnuté heslo

Zadajte e-mailovú adresu, s ktorou ste vytvárali účet. Budú Vám na ňu zasielané informácie k nastaveniu nového hesla.

Prihlásenie

Nemáte účet?  Registrujte sa

#ADS_BOTTOM_SCRIPTS#